拋光，就是將不銹鋼的表面進行特殊化的處理，使之看起來更加的光滑，能夠使酒罐達到一致的平整度，這樣無論是從賣相上來說還是從實用性上來說，都要上一個層次。拋光的工藝我們已經有所了解了，但是具體的做法是怎樣的呢?白酒釀酒設備在使用時其最大的特點就是不生銹，其實其不生銹也是相對的，若長時間受外界環境的影響和一些人們因素，其表面也會被氧化，從而造成設備的生銹影響正常使用，因此為了使其能夠更好的為我們服務，我們需要對其進行拋光處理。

　　Polishing, is specialized for processing the surface of the stainless steel, so it looks more smooth, can make the wine can reach the smoothness of the same, so whether it is from the appearance it is from the practical view, should be on a level. Polishing process we already know, but the specific practice is what kind of? In the use of liquor brewing equipment the biggest advantage is that it does not rust, in fact it does not rust is relative, if long time affected by the external environment factors and some people, the surface will be oxidized, resulting in equipment the rust of normal use, so in order to enable it to serve us better, we need to carry on the polishing treatment.

　　白酒釀酒設備的表面拋光步驟：

　　Surface polishing steps for liquor making equipment:

　　1、粗磨，用600#的砂帶在三面上往返磨削工件，本工序要達到的目標是去掉工件焊接留下的焊點，以及在上步工序出現的碰傷，達到焊口圓角初步成型，水平面和垂直面基本無大劃痕，無碰傷，經此步工序后工件表面的粗糙度應能達到R0.8mm。注意在拋光過程中注意砂帶機的傾斜角度和控制好砂帶機對工件的壓力。一般來說以與被拋面成一條直線比較適中!

　　1, coarse grinding, and grinding the workpiece on the three side with the 600# belt, the process to achieve the goal is to remove the solder welding left, and bumps appear in the process step, to weld fillet shape, horizontal and vertical surface with no scratches, no scratches, after this step after the workpiece surface roughness can reach R0.8mm. Attention should be paid to the tilt angle of the belt conveyor and the pressure of the belt conveyor on the workpiece during the polishing process. Generally speaking, it is more reasonable to make a straight line with the thrown face

　　2、半精磨，用800#的砂帶按照前面往返磨削工件的方法中磨工件的三面，主要是對前面工序出現的接縫進行修正以及對粗磨后產生的印痕進行進一步的細磨，對前面工序留下的印痕要反復磨削，達到工件表面無劃痕，基本變亮。本工序表面粗糙度應能達到R0.4mm。(注意本工序不要產生新的劃痕及碰傷，因為在后面的工序無法修補此類缺陷。)

　　2, semi fine grinding, grinding method with 800# belt in front of round-trip grinding in three, mainly on the previous process of joint of the correction and the coarse grinding marks for further fine grinding, leaving marks to the previous process repeated grinding, no scratches to the surface of the workpiece, basic light. The surface roughness of this process should be up to R0.4mm. (note that new scratches and bumps are not allowed in this process because the defects cannot be repaired in the subsequent process. )

　　3、精磨，用1000#的砂帶主要是對前步工序出現的細小紋線的修正磨削，磨削方法與上同。本工序要達到的目標是磨削部分與工件未磨削部分的接縫基本消失，工件表面進一步光亮，通過本工序磨削后的工件要基本接近鏡面效果，工件表面粗糙度應能達到R0.1mm。

　　3, fine grinding, using 1000# abrasive belt, mainly for the front steps of the small lines of grinding, grinding, grinding method and the same. This procedure is to achieve the goal of grinding part and workpiece grinding part of the seam not disappeared, the surface of the workpiece through further light, the workpiece process after grinding to close to the mirror effect, the surface roughness of the workpiece should be able to reach R0.1mm.

　　白酒釀酒設備的表面拋光的注意事項：1、必須經專業培訓人員方可使用。2、拋光中嚴禁長時間在某一處原地研磨，以免拋漏底漆。3、拋光過程中應及時清理研磨盤上的氧化層污垢及研磨劑等物，避免固化難處理及再拋光時劃傷車漆。4、酒罐拋光需保持研磨盤的潔凈，提高施工的效率。

　　Attention should be paid to the surface polishing of liquor making equipment: 1. It must be used by professional training staff. 2, polishing is prohibited for a long time in a place to avoid grinding, polishing paint leakage. 3, polishing process should be cleared in time on the grinding pad oxidation layer, dirt and abrasives and other things, to avoid curing, difficult to handle and polishing when scratching the car paint. 4, the wine tank polishing needs to maintain the grinding plate clean, enhances the construction efficiency.