機械設備在使用過程中一定會因操作者的一些使用不當產生故障，當然白酒釀酒設備也不會幸免于難。但是，如果您能在設備出現故障時能迅速做出反映，立即解除故障，那么機可以防止意外事故的發生。接下來，就請釀酒設備廠家為大家簡單的介紹，希望能對您有所幫助!在釀酒設備故障中最常見的應該是由于設備負荷超載導致的意外事故。負荷超載有可能是以下原因造成的：

　　Mechanical equipment in use in the course of some operators will be due to improper use of failure, of course, liquor, brewing equipment will not survive. However, if you can make a quick response when the equipment fails, and immediately remove the fault, then the machine can prevent accidents. Next, please make wine equipment manufacturers for everyone simple introduction, hope to be helpful to you, in the brewing equipment failure, the most common should be due to equipment overload caused by accidents. Overload may be caused by the following reasons:

　　1、溫控儀表失靈或者熱電偶沒有插好，造成聚合物加工溫度過低，引起負荷超載。

　　1, temperature control instrument failure or thermocouple is not inserted, resulting in polymer processing temperature is too low, causing overloading of the load.

　　2、突然更換原料牌號或者工藝配方，工藝條件沒有及時調整，造成負荷超載。

　　2, suddenly change raw material brand or process formula, process conditions are not adjusted in time, resulting in overload.

　　3、口模、螺桿設計不合理，造成口模壓力過高。

　　3, the die and screw design is unreasonable, resulting in excessive pressure on the die.

　　4、濾板或者過濾網堵塞。這種情況在擠出用劣質無機物填充的材料或者大量使用不潔凈的回收料時，會經常發生。

　　4, filter plate or filter block. This often occurs when extruded materials filled with inferior inorganic materials or a large amount of recycled material are used.

　　5、異物進人機筒會引起負荷超載。比如，較大的銅制品進入機筒，雖然沒有造成螺桿、機筒損壞，但是可能引起負荷超載。

　　5, foreign objects into the machine cylinder will cause overload. For example, larger copper products into the barrel, although not caused by screw, cylinder damage, but may cause overload.

　　當釀酒設備出現故障時應按照以下方法修理：切斷電源和水源，拆卸機頭進行清理后，拆下螺桿和機筒并立即清理。如果不是螺桿損壞，應該將清理好的螺桿涂抹油脂垂直懸掛起來。這時再分析發生事故的原因和部位，并根據該部位的圖樣安排拆卸工作并準備備件。電動機或者軸承發生突然損壞，往往都是在定期維護保養時沒有發現潛在的問題，沒有及時進行更換。因此，只要換上新的備件或是在保養時及時發現問題并解決，一般就可以重新開機。釀酒設備的負荷超載故障往往伴隨有熔體壓力和電流的急劇升高。但是對于釀酒設備生產廠自己制造的減速箱，如果頻繁發生傳動軸、齒輪損壞事故，要考慮可能是減速箱加工精度的問題。

　　When brewing equipment failure, should be repaired according to the following methods: cut off the power supply and water source, remove the nose, after cleaning, remove the screw and barrel, and immediately clean up. If the screw is not damaged, the cleaned screw shall be coated and the grease will be hung vertically. Then analyze the cause and location of the accident and arrange the demolition work and prepare the spare parts according to the drawing of this part. Motor or bearing sudden damage, often in regular maintenance, found no potential problems, did not change in time. Therefore, as long as the new spare parts or maintenance in time to find problems and solve, you can generally re boot. The overload failure of brewing equipment is often accompanied by a dramatic increase in melt pressure and current. But for the reduction gearbox made by the brewery equipment factory, if the transmission shaft and gear damage occur frequently, it is necessary to consider the problem of the machining accuracy of the reduction case.